Do It Yourself Bath Setup.
Do It Yourself Bath Setup.
Blog Article
We have found this article involving How to Install a Bathtub: Install an Acrylic Tub and Tub Surround down the page on the web and felt it made perfect sense to relate it with you here.
Setting up a bath tub isn't specifically rocket science, yet it does require solid plumbing, carpentry, as well as often, tiling skills. Changing an old bathtub with a brand-new one is additionally a moderately hard job. If the old tub is easily available, the task can move easily; if you have to open a wall to eliminate the old bathtub and position the new tub, the job is much harder. In either case, the job is within a residence handyman's skills, although you will need an assistant to vacate the old tub and set in the brand-new one. Make certain you have actually qualified yourself for the task as well as fit trying it. As opposed to working with a contractor to take over a halfway-completed project, it is much better to consider employing one before you begin. Chances are you may require an expert plumber to make tube connections.
This article will certainly assist you install a new bathtub in your bathroom if you have actually currently bought a new bathtub and do not require to transform the setup of your previous water supply pipes.
Your tools and product list need to comprise the following:
Removing Old Touches
If you require to replace old taps with new ones as a part of your installment, then the first thing you ought to do is disconnect the water. After doing so, switch on the taps to drain pipes any kind of water continuing to be in the system. The process of eliminating the existing faucets can be fairly problematic due to the restricted access that is usually the instance.
Utilize a container wrench (crowsfoot spanner) or a tap tool to undo the nut that connects the supply pipelines to the taps. Have a fabric prepared for the staying water that will come from the pipes. Once the supply pipes have been removed, make use of the very same device to loosen up the nut that holds the taps onto the bath/basin. You will need to quit the solitary faucets from transforming during this process. Once the taps have actually been eliminated, the holes in the bath/basin will need to be cleansed of any type of old sealing compound.
Before going on to fit the brand-new faucets, compare the pipe links on the old faucets to the new taps. If the old faucets are longer than the brand-new taps, then a shank adapter is needed for the brand-new taps to fit.
Suitable New Touches
If the tails of the new taps are plastic, after that you will certainly need a plastic connector to stop damages to the thread. One end of the adapter fits on the plastic tail of the faucet as well as the other end gives a link to the existing supply pipes.
If you require to fit a monobloc, after that you will require minimizing couplers, which links the 10mm pipe of the monobloc to the common 15mm supply pipe.
Next, place the tap in the mounting opening in the bath/basin guaranteeing that the washers remain in place in between the tap and the sink. Safeguard the tap in position with the producer given backnut. When the tap is safely in place, the supply pipelines can be connected to the tails of the faucets. The taps can either be attached by utilizing corrugated copper piping or with normal faucet connectors. The previous type needs to be connected to the faucet ends initially, tightening just by hand. The supply pipes can later on be connected to the various other end. Tighten both ends with a spanner after both ends have actually been connected.
Mounting the Bathtub
Utilizing the two wood boards under its feet, place the tub in the called for position. The wood boards are useful in equally spreading out the weight of the bathtub over the location of the boards instead of concentrating all the weight onto 4 small factors.
The next objective is to ensure that the tub is leveled all round. This can be achieved by inspecting the level and also adjusting the feet on the tub up until the level reads level.
To set up faucets, fit all-time low of the outermost adaptable tap connector to the appropriate supply pipe by making a compression join; after that do the exact same for the various other faucet.
Activate the water supply and inspect all joints and also brand-new pipework for leaks and tighten them if required. Load the bath tub as well as also inspect the overflow electrical outlet as well as the regular electrical outlet for leaks.
Finally, repair the bathroom paneling as defined in the supplier's instruction manual. Tiling and also securing around the tub needs to wait until the bathtub has been made use of at least once as this will certainly resolve it into its final position.
Getting ready for the Installation
First of all, the supporting frame supplied with the bath must be fitted (if needed) according to the manufacturer's instructions. Next off, fit the faucets or mixer to the bath tub. When suitable the faucet block, it is very important to see to it that if the tap features a plastic washer, it is fitted between the bath and also the faucets. On a plastic bathroom, it is additionally reasonable to fit a supporting plate under the taps unit to avoid stress on the tub.
Fit the adaptable faucet ports to the bottom of both faucets using 2 nuts and olives (sometimes supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and then pass the outlet with the hole in the bathroom. Utilize the nut provided by the maker to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the versatile overflow pipe to the overflow outlet. Afterwards, screw the pipeline to the overflow face which ought to be fitted inside the bath. Ensure you make use of all of the provided washers.
Attach the trap to the bottom of the waste outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the electrical outlet. Link the bottom of the overflow tube in a similar manner.The bath should currently be ready to be fitted in its last placement.
Tiling Around the Tub
In the location where the bath fulfills the floor tile, it is required to seal the accompanies a silicone rubber caulking. This is necessary as the fitting can move sufficient to fracture a stiff seal, triggering the water to penetrate the wall in between the bathroom and the tiling, leading to difficulties with moisture and also feasible leaks to the ceiling listed below.
You can pick from a range of coloured sealers to assimilate your fixtures and installations. They are offered in tubes and cartridges, and also can sealing gaps approximately a width of 3mm (1/8 inch). If you have a bigger gap to fill up, you can fill it with spins of soaked newspaper or soft rope. Keep in mind to always fill the bathtub with water prior to sealing, to allow for the activity experienced when the tub is in usage. The sealant can split fairly very early if you do not take into consideration this movement prior to sealing.
Conversely, ceramic coving or quadrant tiles can be used to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are additionally quickly offered on the market. It is suggested to fit the ceramic tiles making use of waterproof or water-proof sticky and also grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
As a person who reads on Installing A Bathtub, I figured sharing that excerpt was appropriate. If you please take the time to distribute this blog if you enjoyed it. Thank-you for your time spent reading it.
Schedule Free Estimate Report this page